The inverter is a basic component of Solar Power (PV) systems, it converts Direct Current (DC) electricity from the batteries or in the case of grid-connect system, directly from the PV array into high voltage 220 Alternating current (AC) power as needed. Inverters of the past were inefficient and unreliable while today's generation of inverters are very efficient (85 to 94%) and reliable. Grid-connect inverters are also known as synchronous inverters.

There are two types of stand-alone inverters worth considering, modified sine and sine wave inverters. Square wave inverters are also available, however these are not suitable for all appliances and should be avoided. Modified sine wave units are less expensive per watt of power and do a good job of operating all but the most delicate appliances. They also have a high surge capacity which enables them to start motors whilst their high efficiency lets them run small appliances economically. Most loads will run without any problems from a modified sinewave inverter. However, some appliances will either not operate or not operate as well using a modified sine wave inverter e.g. laser printers, copiers, some computers, light dimmers and some variable speed tools may not operate; some TV's and audio equipment may pick up interference. Digital clocks may not keep time and microwave ovens will have longer cooking times. Small battery chargers may fail as can central heating ignition systems.

Sine wave units produce power which is almost identical to the utility grid, will operate any appliance within their power range, and cost more per watt of output.

Utility-tie systems/sine wave inverters for utility interactive photovoltaic applications, provide direct conversion of solar electric energy to utility power with or without a battery storage system. These systems are designed to meet or exceed utility power company requirements and can be paralleled for any power level requirement.

Inverter Component Checklist:
While an inverter can account for a good portion of the cost of a PV system, it is really a subsystem that requires a number of additional components. To make a safe, reliable, regulation compliant installation one should provide the following:

	Inverter to battery cabling Because of the high current required on low voltage circuits, this cable is large, commonly #2 to 4/0 in size. Smaller conductors than required are unsafe and will not allow the inverter to perform to its full rating.
	DC input disconnect and overcurrent protection It is important to have safe installation with a properly sized DC rated, UL listed disconnect. Typically the disconnect works in conjunction with an overcurrent protection device such as a fuse or circuit breaker. These components are usually installed in an enclosure which can also house shunts and additional equipment or circuit breakers.
	Shunts Used to read the amperage flowing between the battery and inverter, this device is installed in the negative conductor. It can easily be housed in the disconnect or its own enclosure.
	AC output disconnect and overcurrent protection If the breaker panel, which is fed from the inverter, is adjacent to the inverter, then the main breaker will serve as the inverter output disconnect and overcurrent protection. If, however, this panel is not grouped with the inverter, then a separate unit should be installed. This also holds true for AC circuits coming into the inverter from a generator or utility source. A second breaker may be needed if these breakers are not grouped.

Built-In Battery Chargers:
Most larger inverters can operate as battery chargers as well. This is easily and economically accomplished because of the design of most inverters. Inverters step up low voltage DC power and change it to 120VAC power. Battery chargers do the reverse of this.

Transfer switches are also incorporated into these Inverter / Chargers so that the AC loads can be powered directly from the generator when the battery charger is operating.

From a reliability, performance, and economical standpoint, built-in battery chargers are the way to go.

Multi-Stage Battery Charging:
A typical 12-volt lead-acid battery must be taken to approximately 14.2-14.6 VDC before it is fully charged. (For 24 volt systems double these figures for 48 volt, multiply by four.) If taken to a lesser voltage level, some of the sulphate deposits that form during discharge will remain on the battery's lead plates. Over time, these deposits will cause a 200 amp-hour battery to act more like a 100 amp-hour battery, and battery life will be shortened considerably. Once fully charged, batteries should be held at a lower float voltage to maintain their charge - typically 13.2 to 13.4 volts. Higher voltage levels will "gas" the battery and boil off electrolyte, requiring more frequent maintenance.

Most automotive battery charger designs cannot deal with the conflicting voltage requirements of the initial "bulk charge" and subsequent "float" or maintenance stage. These designs can accommodate only one charge voltage, and therefore must use a compromise setting - typically 13.8 volts. The result is a slow incomplete charge, sulphate deposit build-up, excessive gassing and reduced battery life.

More advanced inverter / chargers such as the Xantrex, automatically cycle batteries through a proper three stage sequence (bulk, absorption and float) to assure a rapid and complete charge without excessive gassing.

Factory battery charger settings on most inverter-charger combinations are optimal for a lead acid (liquid electrolyte) battery bank of 250-300 amp hours in a 70°F environment. If your installation varies from these conditions, you will obtain better performance from your batteries if you adjust the control settings.

The Maximum Charge Rate in amps should be set to 20-25% of the total amp-hour rating of a liquid electrolyte battery bank. For example, a 400 amp-hour bank should be charged at no more than an 80 -100 amp rate. Excessive charge rates can damage batteries and create a safety hazard.

The Bulk Charge Voltage of typical liquid electrolyte lead acid batteries should be about 14.6 VDC. There is no one correct voltage for all types of batteries. Incorrect voltages will limit battery performance and useful life. Check the battery manufacturer's recommendations.

The Float Voltage setting should hold the batteries at a level high enough to maintain a full charge, but not so high as to cause excessive "gassing" which will "boil off" electrolyte. For a 12-volt liquid electrolyte battery at rest, a float voltage of 13.2-13.4 is normally appropriate; gel cells are typically maintained between 13.5 and 13.8. If the batteries are being used while in the float stage, slightly higher settings may be required.

Charge voltage guidelines used here are based on ambient temperatures of 70°F. If your batteries are not in a 70°F environment, the guidelines are not valid. Temperature Compensation automatically adjusts the voltage settings to compensate for the differences between ambient temperature and the 70°F baseline. Temperature compensation is important for all battery types, but particularly gel cell, valve-regulated types which are more sensitive to temperature.

Comparing Inverters:
When selecting an inverter, the following should be taken into account: